American access system ADV-1000 Guía de usuario Pagina 236
- Pagina / 777
- Tabla de contenidos
- MARCADORES
Valorado. / 5. Basado en revisión del cliente
236 WIN-PAK User Guide
Poll Response Normal The control panel is responding normally to
computer polling.
Tamper Switch Alarm The control panel service door is open.
Tamper Switch Normal The control panel service door is closed.
PRO-2200 SIO Board Action Group
Action Message/Description
Primary Power Failure Primary power is down. Make a service
call.
Primary Power Normal You have about 2 hours of backup power.
Tamper Switch Alarm The PRO-2200 enclosure is open. Check
to see if service is being done or dispatch
security as needed.
Note: The tamper switch is a Norther
Computers switch. When the door to the
enclosure is opened (switch open),
the firmware reports a Tamper Switch
Alarm immediately, which is also shown at
the same time as a Tamper Switch
Alarm in the Alarm View of WIN-PAK.
Tamper Switch Normal The PRO-2200 enclosure is now closed.
Note: When the door to the enclosure is
closed (switch closed), the firmware
reports a Tamper Switch Normal after
approximately 3 seconds, which is also
shown at that time as a Tamper Switch
Normal in the Alarm View of WIN-PAK.
PRO-2200 Direct Connect and PRO-2200 (Panel
PRO-2200) Action Groups
Action Message/Description
Incorrect Password An incorrect password attempt was made
to access the controller.
Panel Configuration Error An error was generated by an incorrect
panel configuration.
Poll Response Alarm The panel has failed to respond to a poll.
Poll Response Normal The panel has returned a normal response
to a poll.
Primary Power Failure Primary power is down. Make a servicecall. You have
about 2 hours of backup power.
Primary Power Normal Primary power has been restored.
Tamper Switch Alarm The PRO-2200 enclosure is open. Check to
see if service is being done or dispatch
security as needed.
- User Guide 1
- 2 WIN-PAK User Guide 2
- 4 WIN-PAK User Guide 4
- User Non-disclosure Agreement 5
- 6 WIN-PAK User Guide 6
- 8 WIN-PAK User Guide 8
- 10 WIN-PAK User Guide 10
- Table of Contents 11
- User Overview 81 12
- Programming 173 12
- Badging 511 15
- Card Holders 577 17
- Translation 641 18
- Index 771 19
- Database Maintenance 723 19
- Glossary 747 19
- 20 WIN-PAK User Guide 20
- Contact Us 22
- About This Guide 23
- Chapter 5: Badging 24
- Chapter 6: Card Holders 24
- Chapter 7: Translation 24
- Chapter 8: Reports 24
- Conventions 25
- Online Help 26
- Introduction 27
- 28 WIN-PAK User Guide 28
- Access Control with WIN-PAK 29
- WIN-PAK Features 30
- Access Control Management 31
- Cards and Card Holders 32
- Software Concepts 33
- Data Trees 35
- Multiple Server Design 36
- Database Server 37
- Communication Servers 37
- 38 WIN-PAK User Guide 38
- Installation 39
- 40 WIN-PAK User Guide 40
- System Requirements 41
- Recommended Configuration 42
- Performance Configuration 42
- Video Capture Card 43
- Badging Printers 43
- Installation Overview 44
- System Setup 45
- Standalone Systems 45
- Networked Systems 46
- Upgrades 47
- WIN-PAK Installation 48
- Installation Procedure 49
- 50 WIN-PAK User Guide 50
- 52 WIN-PAK User Guide 52
- 56 WIN-PAK User Guide 56
- First Log In 58
- From the WIN-PAK Server 60
- User Interface Workstation 61
- Concurrent Connections 62
- PAK Servers (Services) 64
- 66 WIN-PAK User Guide 66
- 5 Click OK to save changes 68
- Windows XP SP2 69
- 70 WIN-PAK User Guide 70
- Exceptions tab 71
- 72 WIN-PAK User Guide 72
- 6. Click OK to save changes 73
- 74 WIN-PAK User Guide 74
- Connection Properties window 75
- Firewall 75
- Uninstalling WIN-PAK 76
- Service Manager 76
- System Manager 77
- Licensing and Registration 78
- Registering Software Online 79
- License Files 79
- Norton Speed Disk Utility 80
- 82 WIN-PAK User Guide 82
- Operator Guide Overview 83
- User Interface 83
- 84 WIN-PAK User Guide 84
- Right-Click Menus 87
- Database Windows 88
- Database Record Lists 89
- Database Operations 91
- Isolating Database Records 91
- Copying Database Records 92
- Printing Database Reports 93
- Tree Structures 94
- Logging In to WIN-PAK 95
- System Settings 96
- Operator Level Database 97
- 98 WIN-PAK User Guide 98
- Configuring Operator Levels 99
- 100 WIN-PAK User Guide 100
- 102 WIN-PAK User Guide 102
- Copying an Operator Level 103
- Editing Operator Levels 104
- Isolating an Operator Level 105
- Operator Database 107
- Search Field 108
- Criteria 109
- Search For 110
- Searching by Last Log in 111
- Adding Operators 112
- Operator Type Information 112
- Setting Operator Passwords 113
- Working with Passwords 114
- Operator Information 114
- Workstation Defaults 115
- 116 WIN-PAK User Guide 116
- Alarm Printer 117
- Directories 119
- Wallpaper 120
- User Overview 121
- Operator 122
- System Defaults 123
- Alarm Handling 124
- 126 WIN-PAK User Guide 126
- EMail Configuration 128
- Login/Logout 129
- Access Levels 130
- Operations 131
- Locate Card Holder 132
- Searching by Card Number 133
- Searching by Name 133
- System Events 134
- Event View 135
- Filtering Event Views 136
- Alarm View 138
- Alarm View Right-Click Menus 140
- Filtering Alarm View 140
- 142 WIN-PAK User Guide 142
- Alarm View Details 143
- AutoCard Lookup 144
- Activating AutoCard Lookup 145
- 146 WIN-PAK User Guide 146
- Live Monitor View 147
- Controlling the Camera 148
- Adjusting Focus 149
- Adjusting Aperture 149
- Adjusting Zoom 149
- Camera Pan and Tilt Control 149
- Setting Pan and Tilt Limits 150
- Clearing Limits 150
- Setting Home Position 150
- WIN-PAK CCTV Options 151
- Floor Plan View 152
- Changing the Floor Plan View 154
- Show View and View Area 154
- 156 WIN-PAK User Guide 156
- Panel Buffer Commands 157
- Control Map 158
- Command Files 160
- Guard Tour 161
- Starting a Guard Tour 161
- 162 WIN-PAK User Guide 162
- Tracking and Muster 164
- Refreshing the Muster View 166
- Printing a Muster Report 167
- Digital Video 168
- Filter Control 169
- Digital Camera Controls 170
- Right-Click Menu Options 171
- 172 WIN-PAK User Guide 172
- Programming 173
- 174 WIN-PAK User Guide 174
- Programming Overview 175
- 2 - Create Accounts 176
- 4 - Define the Device Map 177
- Control Areas 178
- 6 - Create Floor Plan Views 179
- 7 - Guard Tour 179
- Passwords 180
- Admin Password 181
- Working with Accounts 182
- Selecting an Account 183
- Adding or Editing Accounts 184
- Deleting Accounts 184
- Quick-Start Wizard 185
- 186 WIN-PAK User Guide 186
- Procedure 187
- 188 WIN-PAK User Guide 188
- 190 WIN-PAK User Guide 190
- The Reader screen appears 192
- 194 WIN-PAK User Guide 194
- Time Management 196
- Time Zone Database 197
- 198 WIN-PAK User Guide 198
- Adding Time Zones 199
- 200 WIN-PAK User Guide 200
- Editing Time Zones 201
- Isolating Time Zones 201
- 202 WIN-PAK User Guide 202
- Scheduler 203
- 204 WIN-PAK User Guide 204
- Dial Remote Area 205
- Run Command Files 205
- 206 WIN-PAK User Guide 206
- Holiday Groups 208
- Defining Holiday Groups 209
- 210 WIN-PAK User Guide 210
- Editing a Holiday Group 211
- Isolating Holiday Groups 212
- Daylight Savings Groups 214
- 216 WIN-PAK User Guide 216
- Device Map 217
- Device Maintenance 218
- Using the Device Map 218
- Abstract Devices 219
- Abstract Device Definitions 220
- Setting Up ADVs 221
- 222 WIN-PAK User Guide 222
- Abstract Device Database 224
- Action Groups 226
- 227
- ADV Action Groups 228
- C-100 (Loop) Action Group 229
- 230 WIN-PAK User Guide 230
- Door (Entrance) Action Group 231
- Door Output Action Group 232
- Group Action Group 232
- Guard Tour Sequenced Group 232
- Guard Tour Server Group 232
- NS2+ Action Group 234
- IV) Action Groups 235
- PRO-2200) Action Groups 236
- PRO-2200 Reader Action Group 237
- Supervised) Action Group 238
- RS-232 Action Group 238
- Schedule Server Action Group 239
- Tracking Server Action Group 239
- Communication Server 240
- 242 WIN-PAK User Guide 242
- 244 WIN-PAK User Guide 244
- Command File Server 245
- 246 WIN-PAK User Guide 246
- Schedule Server 247
- 248 WIN-PAK User Guide 248
- Guard Tour Server 249
- 250 WIN-PAK User Guide 250
- Tracking and Muster Server 251
- 252 WIN-PAK User Guide 252
- Access DVPRO 253
- Configuring Fusion 255
- 256 WIN-PAK User Guide 256
- Communication Loops 257
- Adding C-100 Panel Loop 258
- 260 WIN-PAK User Guide 260
- 262 WIN-PAK User Guide 262
- IP Address 264
- Encryption Password 264
- Adding a PRO-2200 Panel Loop 265
- 266 WIN-PAK User Guide 266
- Adding a CCTV Switcher 268
- 270 WIN-PAK User Guide 270
- 272 WIN-PAK User Guide 272
- Adding an RS-232 Connection 273
- Editing Panel Loops 274
- Modem Pools 275
- 276 WIN-PAK User Guide 276
- 278 WIN-PAK User Guide 278
- Panel Defaults 280
- Configuration 282
- 284 WIN-PAK User Guide 284
- 288 WIN-PAK User Guide 288
- Setting Up an RS-232 Loop 289
- 290 WIN-PAK User Guide 290
- Settings 291
- PRO-2200 Modem Pool 292
- 294 WIN-PAK User Guide 294
- 296 WIN-PAK User Guide 296
- Adding Panels in WIN-PAK 297
- Adding PW-2000 Panels 299
- Configuring PW-2000 Panels 299
- 300 WIN-PAK User Guide 300
- Panel Configuration – Basic 301
- 302 WIN-PAK User Guide 302
- ABA Card Format 304
- Wiegand Card Formats 304
- 306 WIN-PAK User Guide 306
- Anti-Passback 308
- Panel Configuration – Options 308
- Forgiveness 309
- PIN and Time Zone for PIN 310
- Continuous Card Reads 310
- Reverse Read LEDs 311
- Split Time Zone 311
- Command File 311
- Initialization Command 311
- Site Codes 311
- Hardware Options 312
- Host Grant 312
- Advanced Options 313
- 314 WIN-PAK User Guide 314
- Number of Cards (U Option) 315
- Outputs for Duress 315
- Panel Configuration – Inputs 316
- 318 WIN-PAK User Guide 318
- Panel Configuration – Outputs 320
- Panel Configuration – Groups 323
- 324 WIN-PAK User Guide 324
- Panel Configuration – Readers 326
- Interpreting Door Interlocks 327
- Free Egress Input 327
- 328 WIN-PAK User Guide 328
- Direct Point 329
- Status Input 330
- Panel Configuration – Finish 331
- Component A 332
- Component B 332
- Adding NS2+ Panels 334
- 336 WIN-PAK User Guide 336
- Global Anti-Passback 340
- Panel Configuration - Inputs 345
- 346 WIN-PAK User Guide 346
- Panel Configuration - Outputs 348
- Panel Configuration - Readers 350
- Defining Door ADVs 353
- 354 WIN-PAK User Guide 354
- Setup the Panel ADV 356
- Serial RS232 Options 358
- TCP/IP Options 359
- 360 WIN-PAK User Guide 360
- Modem Pools) 361
- 362 WIN-PAK User Guide 362
- 366 WIN-PAK User Guide 366
- Formatting Wiegand Cards 368
- 370 WIN-PAK User Guide 370
- 372 WIN-PAK User Guide 372
- 374 WIN-PAK User Guide 374
- Setting Up Reader Boards 376
- 380 WIN-PAK User Guide 380
- Processing Mode and Results 383
- Control Flags and Results 385
- Door Interlocks 388
- 392 WIN-PAK User Guide 392
- Standard Reader Types 394
- 396 WIN-PAK User Guide 396
- Mode Descriptions 397
- 398 WIN-PAK User Guide 398
- Interlocking 400
- 404 WIN-PAK User Guide 404
- 406 WIN-PAK User Guide 406
- 16-Relay Output Module Setup 409
- 412 WIN-PAK User Guide 412
- 414 WIN-PAK User Guide 414
- Output Settings 414
- Control Point window (below) 415
- 416 WIN-PAK User Guide 416
- 16-Zone Input Module Setup 419
- 422 WIN-PAK User Guide 422
- 424 WIN-PAK User Guide 424
- 428 WIN-PAK User Guide 428
- 432 WIN-PAK User Guide 432
- 434 WIN-PAK User Guide 434
- Triggers and Procedures 437
- 438 WIN-PAK User Guide 438
- Adding a New Procedure 439
- 440 WIN-PAK User Guide 440
- 442 WIN-PAK User Guide 442
- Adding a New Trigger 443
- 444 WIN-PAK User Guide 444
- Control Point ADVs 447
- 448 WIN-PAK User Guide 448
- Editing Panels 450
- Initializing Panels 451
- 452 WIN-PAK User Guide 452
- Panel Initialization Options 454
- Initializing Status 455
- Access Areas 456
- 458 WIN-PAK User Guide 458
- Renaming a Branch 459
- Tracking and Mustering Areas 460
- Nesting Areas 462
- 464 WIN-PAK User Guide 464
- Muster System Precautions 465
- At the Time of Muster 466
- 468 WIN-PAK User Guide 468
- 470 WIN-PAK User Guide 470
- Area Tree 472
- Adding Devices to Branches 473
- 474 WIN-PAK User Guide 474
- Showing Available Devices 475
- Floor Plans 477
- Floor Plan Definition 478
- Adding a Floor Plan 479
- 480 WIN-PAK User Guide 480
- ADV Icons 482
- 484 WIN-PAK User Guide 484
- 486 WIN-PAK User Guide 486
- Link Properties 487
- Text Properties 488
- Editing a Floor Plan 489
- Guard Tours 490
- 492 WIN-PAK User Guide 492
- Unsequenced Check Points 493
- 494 WIN-PAK User Guide 494
- Sequenced Check Points 496
- Check Point Alarms 497
- Setting Check Point Alarms 498
- Command File Database 501
- 502 WIN-PAK User Guide 502
- Available Commands 504
- Adding Custom Commands 505
- Editing Command Files 506
- 510 WIN-PAK User Guide 510
- Chapter 5 511
- Badge Layouts Database 511
- Badge Definition Window 511
- 512 WIN-PAK User Guide 512
- 514 WIN-PAK User Guide 514
- Copying a Badge Layout 515
- Editing a Badge Layout 516
- Creating Badges 517
- Ruler Definitions 520
- Zoom Factor 520
- Snap and Grid Settings 520
- Blockouts 521
- Setting a Blockout 522
- Badge Objects: Introduction 523
- Moving Objects 524
- Badge Object Properties 525
- Options on the Badge Tab 527
- Background 528
- Positioning Badge Elements 530
- Video Backgrounds 532
- Capturing a Video Background 534
- Video Settings 535
- Photo Settings 536
- Working with Colors 537
- Creating Custom Colors 538
- Red Green Blue 539
- Color Solid 540
- Selecting Custom Colors 540
- Magnetic Stripe Encoding 542
- 544 WIN-PAK User Guide 544
- Adding and Editing Text 546
- Changing Fonts and Sizes 548
- Changing Text Color 548
- 550 WIN-PAK User Guide 550
- Deleting a Text Block 551
- 552 WIN-PAK User Guide 552
- Badge Objects: Barcodes 553
- 554 WIN-PAK User Guide 554
- Formatting a Barcode 556
- Barcode Options 557
- Editing Barcode Colors 558
- Positioning a Barcode 559
- Deleting a Barcode 560
- Badge Objects: Shapes 561
- 562 WIN-PAK User Guide 562
- Positioning Shapes 563
- Deleting a Shape 564
- Placeholder 565
- 566 WIN-PAK User Guide 566
- 568 WIN-PAK User Guide 568
- Positioning a Graphic Image 569
- Deleting a Graphic Image 570
- Configuring the Badge Printer 571
- 572 WIN-PAK User Guide 572
- Badge DLLs 574
- 576 WIN-PAK User Guide 576
- Card Holders 577
- 578 WIN-PAK User Guide 578
- Overview 579
- 580 WIN-PAK User Guide 580
- 582 WIN-PAK User Guide 582
- 584 WIN-PAK User Guide 584
- 586 WIN-PAK User Guide 586
- Note Field Mask Properties 588
- Mask Descriptions 589
- Mask Character Descriptions 589
- 590 WIN-PAK User Guide 590
- Setting Up Card Holder Tabs 591
- Adding a Card Holder Tab 592
- Configuring AutoCard Lookup 594
- Setting Up Card Holders 596
- Adding Card Holders 596
- 598 WIN-PAK User Guide 598
- Deleting a Card Holder Record 599
- 600 WIN-PAK User Guide 600
- Card Holder Photos 602
- (next illustration): 603
- 604 WIN-PAK User Guide 604
- Deleting a Card Holder Photo 606
- Capturing Card Holer Photos 606
- Grab Settings 609
- Card Holder Signatures 610
- 612 WIN-PAK User Guide 612
- Adding an Access Level 616
- Configuring an Access Level 618
- Custom Access Levels 620
- Customizing One Entrance 621
- Access Level 622
- Show Original Access Level 623
- Working with Cards 624
- 626 WIN-PAK User Guide 626
- Adding an Individual Card 627
- Card Properties 628
- 630 WIN-PAK User Guide 630
- Deleting a Card 631
- Bulk Card Add and Delete 632
- Bulk Card Delete 634
- Associating Badges and Cards 635
- Assigning a Badge to a Card 636
- Previewing and Printing Cards 637
- 638 WIN-PAK User Guide 638
- Printing a Card 639
- 640 WIN-PAK User Guide 640
- Translation 641
- 642 WIN-PAK User Guide 642
- 644 WIN-PAK User Guide 644
- 646 WIN-PAK User Guide 646
- 648 WIN-PAK User Guide 648
- Editing Dialog Text 650
- Changing Menu Text 651
- 652 WIN-PAK User Guide 652
- Searching Menu Text 653
- Sorting Untranslated Items 653
- Changing Other System Text 654
- Testing Translations 656
- Importing a Language File 656
- 658 WIN-PAK User Guide 658
- Chapter 8 659
- 660 WIN-PAK User Guide 660
- 662 WIN-PAK User Guide 662
- Report Window Conventions 663
- Estimating Report Size 664
- Exporting Reports 664
- Previewing Reports 665
- Printing Reports 666
- Report Templates 667
- Access Area Report 668
- Access Level Report 669
- Attendance Report 671
- 672 WIN-PAK User Guide 672
- Card Frequency Report 673
- 674 WIN-PAK User Guide 674
- 676 WIN-PAK User Guide 676
- Card Report 677
- 678 WIN-PAK User Guide 678
- Card History Report 680
- 682 WIN-PAK User Guide 682
- Card Holder Report 684
- 686 WIN-PAK User Guide 686
- Smith is after Mary 686
- 688 WIN-PAK User Guide 688
- Card Holder Tab Layout Report 689
- Command File Report 690
- Control Area Report 692
- Device Map Report 693
- 694 WIN-PAK User Guide 694
- 696 WIN-PAK User Guide 696
- Reporting on Panel Loops 697
- 698 WIN-PAK User Guide 698
- Reporting on Modem Pools 700
- 702 WIN-PAK User Guide 702
- Floor Plan Report 703
- Guard Tour Report 704
- History Report 705
- 706 WIN-PAK User Guide 706
- Transaction Types 707
- Alarm and Card 707
- 708 WIN-PAK User Guide 708
- 710 WIN-PAK User Guide 710
- Holiday Group Report 711
- Note Field Template Report 712
- Operator Report 712
- Operator Actions Report 714
- Operator Level Report 716
- Schedule Report 718
- Time Zone Report 719
- 720 WIN-PAK User Guide 720
- 722 WIN-PAK User Guide 722
- Database Maintenance 723
- 724 WIN-PAK User Guide 724
- 726 WIN-PAK User Guide 726
- 728 WIN-PAK User Guide 728
- 730 WIN-PAK User Guide 730
- 732 WIN-PAK User Guide 732
- 734 WIN-PAK User Guide 734
- Schedule 736
- 740 WIN-PAK User Guide 740
- 746 WIN-PAK User Guide 746
- Glossary 747
- 748 WIN-PAK User Guide 748
- SymbolsSymbols 749
- 750 WIN-PAK User Guide 750
- 752 WIN-PAK User Guide 752
- 754 WIN-PAK User Guide 754
- 756 WIN-PAK User Guide 756
- 758 WIN-PAK User Guide 758
- 760 WIN-PAK User Guide 760
- 762 WIN-PAK User Guide 762
- 764 WIN-PAK User Guide 764
- 766 WIN-PAK User Guide 766
- 768 WIN-PAK User Guide 768
- 770 WIN-PAK User Guide 770
© 2020, manymanuals.es. Todos los derechos reservados | 0.062 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comentarios a estos manuales